Steel & Concrete Pins
LINC Systems carries dozens of concrete pins and steel pins, from 5/8" to 3" concrete pins and drive pins, powder-driven pins and washered insulation pins to 23 gauge headless pins for pin nailers, in .100" to .157" shank diameters, from MAX USA, DEWALT, Simpson Strong-Tie, Aerosmith Fastening, SPOTNAILS and Grabber.
Find the Right Concrete Pins for the Job
This category mixes several kinds of pins. Start with what you are fastening and what you are fastening into, then match the pin to your tool. Sizes below come from the product names on this page.
- Metal track to concrete: pin type: Concrete pins with plastic washer, plastic coil; lengths and shank diameters: 3/4" to 1-1/4"; .102" to .145"; examples on this page: MAX USA CP-C619V6-ICC, CP-C624V6-ICC, CP-C832W7-ICC
- Wood to concrete: pin type: Concrete pins and drive pins; lengths and shank diameters: 1" to 3"; .145" to .157"; examples on this page: MAX USA CP-C864W7-ICC; DEWALT drive pins; Simpson Strong-Tie PDPA-250; Aerosmith PowerPin
- Wood or metal track to steel: pin type: Concrete pins rated for steel, plastic coil; lengths and shank diameters: 5/8" to 2"; .133"; examples on this page: MAX USA CP-W816W4SP-AL (metal track), CP-W833W4SP, CP-W838W4SP, CP-W850W4SP (wood)
- Rigid insulation and insulation board: pin type: Pins with large washers; lengths and shank diameters: 1" to 2-1/2"; 60 mm heads on InsulPin; examples on this page: Aerosmith InsulPin (concrete or steel); Grabber Insulfast washer pins; Simpson Strong-Tie PINW-250
- Trim, molding and small parts: pin type: Headless pins (pin nails); lengths and shank diameters: 5/16" to 2" in 23 gauge; 1/2" in 18 gauge; examples on this page: SPOTNAILS 23 gauge headless pins; SPOTNAILS 18508AZ
- Metal banding: pin type: Metal banding pins; lengths and shank diameters: 1/2"; .109"; examples on this page: Aerosmith FP012C
Not sure which pin your tool takes? Call 800.513.9918 with the tool make and model.
What Are Concrete Pins?
Concrete pins are short, hardened steel fasteners driven straight into concrete, block or structural steel by a power tool. They hold track, plates, furring strips, insulation and fixtures to a hard base without drilling a hole first. Steel pins work the same way into steel framing and beams.
Unlike a common nail, a concrete pin has a smaller head, a hardened shank and a point made for hard material. The pins on this page run from .100" to .157" in shank diameter. Many come with a washer, from a small plastic washer that holds the pin straight in the tool to metal washers up to 1-7/16" that spread the load over soft material.
Concrete pins come loose in boxes for single-shot tools, or collated in plastic coils, wire coils and strips for tools with a magazine. Use the collation your tool is built for.
Steel and Concrete Pins by Job
Metal Track to Concrete
Framers fastening steel stud track to a slab use short, thin pins. The MAX USA PowerLite concrete pins for metal track to concrete come in 3/4" and 1" at .102", plus 1-1/4" at .145", all on plastic coils with a plastic washer.
Wood to Concrete
Sill plates, furring strips and wood blocking need a longer pin to get through the wood and into the concrete. Options here include the MAX USA CP-C864W7-ICC (2-1/2" x .145"), DEWALT drive pins from 1" to 3", Simpson Strong-Tie powder-driven pins at 2-1/2" x .157", and Aerosmith PowerPin concrete pins from 3/4" to 2-1/4".
Wood and Metal Track to Steel
For steel beams and decks, use pins made for steel. MAX USA lists wood to steel pins from 1-1/4" to 2" (.133") and a 5/8" metal track to steel pin. Aerosmith VersaPin steel pins run from 7/8" to 2" at .100" to .102", with grip or helical shanks on some.
Rigid Insulation to Concrete or Steel
Insulation board needs a wide head so the pin does not pull through. The Aerosmith InsulPin has a 60 mm washer, in versions for concrete and for steel. Grabber's Insulfast washer pins come in 1" and 2", and the Simpson Strong-Tie PINW-250 is a powder-actuated, metal-washered pin for insulation board.
Trim and Finish Work with Headless Pins
Headless pins, also called pin nails or micro pins, hold trim, molding and small parts while glue sets, and leave a hole that is hard to see. SPOTNAILS 23 gauge headless pins on this page run from 5/16" to 2" with a chisel point. Drive them with a 23 gauge pinner from our finish, brad and pin nailers.
Metal Banding
The Aerosmith FP012C metal banding pin (1/2" x .109", .25" head) is made for fastening metal banding.
Powder Actuated Pins vs Air-Driven Concrete Pins
Powder Actuated Pins and Drive Pins
A powder-actuated tool uses a small powder load, like a blank cartridge, to drive the pin. Loads come in calibers and power levels; the Simpson Strong-Tie P27SL5A on this page is a .27 caliber, 10-shot strip load at level 5 (red). Use the caliber your tool takes and the lowest level that sets the pin. DEWALT drive pins and Simpson Strong-Tie PDPA pins are powder actuated pins, and the PDPAS pins are collated for tools that feed from a strip. Only trained operators should run powder-actuated tools, following the tool maker's instructions.
Air-Driven Concrete Pins
Air-driven concrete pinners use compressed air instead of powder loads, so there are no loads to buy or store. They feed collated pins from a magazine. LINC's specialty nailers include MAX USA PowerLite high pressure concrete pinners and JITOOL concrete nailers, along with DEWALT powder-actuated tools. MAX USA's PowerLite concrete pins on this page share the PowerLite name with those pinners.
Concrete Pins vs Concrete Nails
"Concrete nails" usually means hardened nails driven by hand or with a concrete nailer. Concrete pins are made for powder-actuated tools and concrete pinners, with thinner shanks and smaller heads. If you are attaching wood strips to concrete with a T-nailer, see our T-nails, and for collated nails with ballistic points, see screw and ballistic nails.
Drive Pin Options: Shank, Point, Washer and Finish
Shank Diameter and Length
Thicker shanks (.145" to .157") suit wood to concrete work. Thinner shanks (.100" to .133") are common for track and steel. Pick a length that gets through the material and into the base by the amount the tool or pin maker calls for.
Shank and Point Types
Smooth shanks are standard. Grip, helical and knurled shanks add grip in the base material. Ballistic points are shaped for hard base material, and the chisel points on headless pins help them start cleanly in wood.
Washers and Finishes
DEWALT drive pins come with 7/8", 1" or 1-7/16" washers, or none. Simpson Strong-Tie PDPAWL pins have a 1" washer. Finishes include brite, zinc plated, galvanized, mechanically galvanized (one Simpson Strong-Tie pin is Class 65) and Aerosmith's PT2000.
How to Choose Concrete Pins, Step by Step
- Name the base. Concrete, block or steel, and how thick the steel is.
- Name the material on top. Wood, metal track, insulation or trim sets the length, head and washer.
- Check your tool. Powder-actuated, air-driven pinner or pin nailer, its length range and the collation it feeds.
- Pick the shank and point. Diameter, shank type and point for the base material.
- Test a few. Drive a few pins in a scrap area and check that they seat flush and hold before running the job.
Need help? Call 800.513.9918 and tell us the base, the material and your tool.
Buy Steel and Concrete Pins from LINC
Buy concrete pins, drive pins and headless pins from LINC by the box. We carry MAX USA, DEWALT, Simpson Strong-Tie, Aerosmith Fastening, SPOTNAILS, Grabber, Beck and NailPro, and the pinners and powder-actuated tools to drive them.
Have a LINC account? Sign in to see your pricing. Ordering for a crew or a project? Ask for a quote or call 800.513.9918. LINC also services pneumatic fastening tools: see tool repair.
Get a Quote or call 800.513.9918
Concrete Pin FAQs
What are concrete pins used for?
Fastening wood, metal track, insulation and fixtures to concrete, block or steel. They are driven by powder-actuated tools or air-driven concrete pinners.
What is the difference between drive pins and concrete pins?
Mostly the name. Drive pins usually means pins for powder-actuated tools, like the DEWALT drive pins here. Concrete pins covers those plus pins for air-driven pinners.
Will these pins fit my tool?
Only if the tool takes that length, shank diameter and collation. Check the tool's listing or call us with the make and model.
Can concrete pins go into steel?
Yes, if the pin is made for steel. Use pins listed for steel, such as the MAX USA wood to steel and metal track to steel pins.
What are headless pins?
Thin 23 gauge or 18 gauge pins with no head, driven by a pin nailer. They hold trim and small parts and leave a very small hole.
Can I get volume pricing on concrete pins?
Yes. Sign in to your LINC account for your pricing, or call 800.513.9918 for a quote.
Another question? Call 800.513.9918 or contact us.

